|
Home :: Technical Resources :: Material Safety Data Sheet :: Part 1
|
MATERIAL SAFETY DATA SHEET
PART II: What should I do if a hazardous situation occurs?
|
|
|
|
PART II: What should I do if a hazardous situation occurs?
|
|
4. FIRST-AID MEASURES
|
|
The following information is pertinent to all nineteen components:
|
|
SKIN EXPOSURE
|
Wear gloves when using system components. If contact with this
product leads to reddening, inflammation, or irritation, flush the exposed area with
running water. Remove any contaminated clothing, taking care not to contaminate eyes.
Avoid contact with Dimethyl Sulfoxide solutions containing toxic substances or
substances with unknown toxicological properties. Dimethyl Sulfoxide is readily absorbed through the skin and may carry such substances into the body.
|
|
EYE EXPOSURE
|
If chemical gets into eyes, open victim’s eyes while under gentle
running water. Use sufficient force to open eyelids. Have victim “roll” eyes. Minimum flushing is for 15 minutes.
|
|
INHALATION
|
If vapor, mist, or dust of this product’s components is inhaled, causing
irritation, remove victim to fresh air. If necessary, use artificial respiration to support
vital functions. Remove or cover gross contamination to avoid exposure to rescuers.
|
|
INGESTION
|
If a component is swallowed, CALL PHYSICIAN OR POISON
CONTROL CENTER FOR MOST CURRENT INFORMATION. If professional
advice is not available, do not induce vomiting. Victim should drink milk, egg whites, or
large quantities of water. Never induce vomiting or give diluents (milk or water) to
someone who is unconscious, having convulsions, or who cannot swallow.
|
Victims of chemical exposure must be taken for medical attention. Rescuers should be
taken for medical attention if necessary. Take copy of label and MSDS to physician or
health professional with victim.
|
|
|
5. FIRE-FIGHTING MEASURES
|
|
The following information is pertinent to all 19 components:
|
|
FLASH POINT, °C (method):
|
Not applicable
|
|
AUTOIGNITION TEMPERATURE, °C:
|
Not applicable
|
|
FLAMMABLE LIMITS (in air by volume, %):
|
Lower (LEL): Not applicable
|
|
Upper (UEL): Not applicable
|
|
FIRE EXTINGUISHING MATERIALS:
|
Use suppression methods for surrounding materials.
|
| Water Spray: | YES |
| Carbon Dioxide: | YES |
| Foam: | YES |
| Dry Chemical: | YES |
| Halon: | YES |
| Other: | Any “B” Class |
|
|
UNUSUAL FIRE AND EXPLOSION HAZARDS: When involved in a fire, this material may decompose and produce irritating fumes and toxic gases including carbon monoxide, carbon dioxide, and oxides of nitrogen.
Explosion Sensitivity to Mechanical Impact: Not sensitive
Explosion Sensitivity to Static Discharge: Not sensitive
SPECIAL FIRE-FIGHTING PROCEDURES: Incipient fire responders should wear eye protection. Structural fire fighters must wear Self-Contained Breathing Apparatus and full protective equipment.
|
|
6. ACCIDENTAL RELEASE MEASURES
|
|
The following information is pertinent to all 19 components
|
|
SPILL AND LEAK RESPONSE
|
|
For small releases, treat the product as water, but take
basic hygiene precautions. Lightweight gloves, a lab coat and eye protection should be
worn. For liquid solutions, absorb spilled liquid with paper towels. Wash contaminated
area with soap and water, absorb with paper towels, and rinse with water.
Large releases which are not immediately controlled, should be responded to by trained
personnel using pre-planned procedures. Proper protective equipment should be used. In
case of a spill, clear the affected area, protect people, and respond with trained personnel.
Minimum Personal Protective Equipment should be Level D: lab gloves, chemically
resistant apron, boots, and splash goggles. Respiratory protection should not be
necessary. Absorb spilled liquid with polypads or other suitable absorbent materials.
Decontaminate the area thoroughly.
Place all spill residue in a double plastic bag and seal. Dispose of in accordance with
Federal, State, and local hazardous waste disposal regulations (see Section 13).
|
 Continue To Part 3
|
|
|
